Polyester Fiberglass Products Composite Mat For Paving

NJEFG

Polyester Fiberglass Composite Mat for Paving

Polyester Fiberglass Composite Mat (Polyester Fiberglass Paving Mat) is produced from the mixture of polyester fiber and glass fiber by wet lay-out process. The combination of glass fiber and polyester fiber is the key to its performance. After mixing the two fibers together, the polyester fiberglass mat keeps good features of both fibers and minimizes shortcomings of both fibers.

Strong tensile strength make polyester-fiberglass composite mat especially suitable for waterproofing of payments; it extends the life of pavement through the delay of reflective cracking. Polyester fiberglass composite mat also serves as an effective moisture barrier. The unique, non-woven, polyester-fiberglass structure of the mat allows asphalt binder to fully penetrate and fill voids within the mat, limiting moisture infiltration and preventing water from infiltrating into the granular layers of the pavement structure.

Polyester- Fiberglass Composite Mat creates innovative solutions to help the paving projects to go smoothly and provides superior performance on airport runway, super highway, parking area and business lots.

【CHARACTERISTICS】

◇ Delays reflective cracking ◇ Provides a Moisture Barrier

◇ Easy installation ◇ Fully Millable and Recyclable

◇ Low risk of product shrinkage during the overlay process

Technical support

If customer meets any problem about technic, Nanjing EFG CO., LTD will supply relative knowledge to help customer find the best solution, and can send technician to customer’s factory for guiding if necessary.

Technical Data

Nature	Units	Typical
Product Code		PF1003/5	PF136-600
Area Weight	G/m2	90-110	130-150
Tensile Strength MD	N/5cm	220	300
Tensile Strength CD	N/5cm	220	300
Polyester fiber content	%	20-40	20-40
Glassfiber content	%	50-70	50-70
Binder content	%	15-25	15-25
Thickness	mm	0.8	≤1.2
Melting point	℃	230	230
Asphalt absorption capacity	L/m2		1.11
elongation MD	%	<5	<5
elongation CMD	%	<5	<5

Remark: 1. The technical data above is for reference only
2. Any special size can also be supplied according to customers’request

这里可以自定义设置

Applications

1. PF1003/5 is used as waterproofing, insulation and soundproof material on the wall and ceiling.

2. PF136-600 is used as paving mat on highway, airport runway and some other business lots.

Technical specification of our products

Our services

◆ Markets

Nanjing EFG CO., LTD. has delivered cargo to USA, EU, Middle East, North Africa, South Africa, Asian customers with ensured quality and rich experience for export deliveiry. Nanjing EFG CO., LTD welcomes cooperation from all of the world.

◆ Storage

This product should be stored in a dry, ventilated and rainproof place, with temperatures from 5℃to 35℃ and humidity between 35% and 65%. It is recommended to be kept in intact package when not used to avoid damp.

◆ After sales service

Nanjing EFG CO., LTD tracks cargo of every shipment till customer uses, and offer any help for customer’s demand in any time.

Loading Cabinet

Customization

Polyester Fiberglass Composite Mat in above table are the standard types Nanjing EFG CO., LTD is delivering to customers, if customer wants specific unit weight, tensile strength, roll width and roll length, Nanjing EFG CO., LTD can produce as per customer’s requirement, offer tailored service to customers from different countries.

Instruction to use the polyester fiberglass paving mat

◆ Remove dirt, gravel and dust from the pavement to assure good adhesion between asphalt and pavement.
◆ If the road is damaged, it must be repaired to make the surface of the road hard and smooth.
◆ For a good result, the asphalt binder that will be used to adhere the Paving Mat to the road must be hot asphalt, but not emulsified asphalt.
◆ The temperature of hot asphalt should be between 163℃ and 204 ℃.
◆ When the hot asphalt covered the road, the Composite Paving Mat must be overlaid onto the hot asphalt before the asphalt lose it’s mobility so as to assure the mat fully soaked by asphalt and effectively provides a moisture barrier.

◆On installation of the Composite Paving Mat, the air temperature must be higher than 4 ℃.

In order to achieve optimal results, here we provide some Notes on installation of Composite Paving Mat:
◆Composite Paving Mat must be installed on hot asphalt. We recommend the following asphalt. AC-20; PG64-22; AR8000 +, or asphalt with penetrate rates 60-80. In extremely hot summer, we recommend to use asphalt with high viscosity, such as AC-30; PG67-22; AR8000 +, or asphalt with penetrate grade 40-60.
◆ The best ratio of asphalt is 1.1 liters / square meters paving mat, but subject to project site situation during the installation, the ratio can be between 1.0-1.3 liters / square meters. According to different area weight of the Composite Paving Mat, the ratio of asphalt should be adjusted accordingly. During the asphalt delivery, we do not advise to heat the asphalt above to a temperature higher than 204 ℃, because this would hinder the pre-mature of liquid asphalt.
◆ Handle the Composite Paving Mat with care during the installation, the paving mat might be damaged or it may cause bad result if the paving mat drop down from the installation machine.

◆During the installation, if it forms a stripe bigger than 2.5cm in any direction, the stripes must be cut and overlaid, and the two layers of paving mat must be fully covered by asphalt so as to assure the two layers of paving mat fully soaked in the hot asphalt. Use roller to press the paving mat or use brush to clear out bubbles in the paving mat to ensure the paving mat fully adhered to the road. When covering the hot asphalt to the road, the width of asphalt should be 4 inch more than the width of paving mat. Since the paving mat can not be curved, for the winding area of the road the paving mat can be cut into several pieces and be installed to the road manually or mechanically.

◆For the connection of two pieces of paving mat: the two pieces of paving mat must be overlapped together. In the longitudinal direction the width of overlapped area must be at least 10.2cm; and in the lateral direction, the width of overlapped area must be at least 5.1cm.

◆ If the installation machine or other vehicles have to drive on the paving mat, it should not turn directions frequently nor suddenly so as to avoid damaging the paving mat. Do not scatter sand or other object on the paving mat; to avoid asphalt sticking to the tire of the machine, do not minimize the ratio of bitumen.

Nanjing Efg Co., Ltd. Has specialized in Fiberglass Materials Supplies Since 2003.

PRODUCT

Polyester Fiberglass Products Composite Mat for Paving

Polyester Fiberglass Products Composite Mat for Paving